Date post: | 26-May-2018 |
Category: |
Documents |
Upload: | phungkhuong |
View: | 216 times |
Download: | 1 times |
CEAG Beiblatt zur Montage- und Betriebsanleitung Zentralbatteriesystem ZB-S, ZB96 und Euro ZB.1400 71 860 193 (B)
Ladeerhaltungsspannung
Einstellen der Ladeerhaltungsspannung am Batterie Control Modul (BCM)
SICHERHEITSHINWEISE
Sicherheitshinweise sind mit diesem Zeichen im Text der Haupt-Bedienungsanleitung gekennzeichnet. Diese sollten vor Beginn der Arbeiten in jedem Fall gelesen werden!
•Einstellarbeiten an der Anlage dürfen nur von Elektrofachkräften durchgeführt werden.
AllgemeinesWerden Zentralbatterieanlagen ohne Batterie geliefert oder ist der Batterietyp unbekannt, so wird die Ladeerhaltungsspannung werksseitig auf einen Wert von 245 V eingestellt (d.h. 2,27 V/Z).
Je nach Batterietyp muss die Ladeerhaltungsspannung vor Ort angeglichen werden.
Die Ladeerhaltungsspannung wird wie folgt eingestellt:
1. ServicePin (1) des BCM für einige Sekunden gedrückt halten bis die grünen LEDs im Wechsel blinken. Die Anzeige am Steuerteil wird jetzt vom BCM gesteuert. Zuvor muss sichergestellt sein, dass keine Ladestörung vorliegt, da hiermit sonst die Fehleranzeige am CU CGS aktiviert wird.
2. Die Spannung „U=“ (2), die jetzt im Display des Steuerteils CU CGS angezeigt wird, ist die einzustellende Ladeerhaltungsspannung. Der angezeigte Strom „I=+“ (3) steht für die Anzahl der gefundenen CMs am CCBBus, 1A = 1CM.
3. Die Ladeerhaltungsspannung nun mit Hilfe der „ISOTest+“ und „ISOTest“ Tasten (4) gemäß den Batterieherstellerangaben einstellen.
ACHTUNG!
Die Ladeerhaltungsspannung wird immer auf den entsprechenden Wert bei einer Temperatur von 20° C eingestellt.
4. Zum Speichern der Spannung erneut die ServiceTaste (1) betätigen und gedrückt halten bis die grünen LEDs aufhören zu blinken. Der EinstellModus wird automatisch nach einer Minute beendet wenn keine IsoTestTaste mehr betätigt wird.
1
4
Anzeige am Steuerteil CU CG-S
14:45:11 02.01.12ČČČČČČČČČČČČČČČČČČČČU=248,0V ċ I=+ 1AT=+23,9 °C BT= 0:00hLadungsstatus 100%
ččččččččččččččččččččCEAG ZB-S Name
2 3
Batterie Control Modul BCM
CEAG Notlichtsysteme GmbHSenatorSchwartzRing 2659494 Soest, GermanyTel.: +49 (0) 2921 69870Fax: +49 (0) 2921 69617Email: info[email protected] Web: www.ceag.de
© 2016 EatonAlle Rechte vorbehaltenPrinted in GermanyPublikationsNr. IL451043MLBestellNr. 40071860193Februar 2016
EatonEMEA HeadquartersRoute de la Longeraie 71110 Morges, SwitzerlandEaton.eu
CEAG Insert to Assembly and Operating Instructions Central Battery System ZB-S, ZB96 and Euro ZB.1 400 71 860 193 (B)
Tripple Charge-Voltage
The Setting of the Tripple Charge-Voltage at the Batterie Control Module (BCM)
SAFETY INSTRUCTIONS
Safety notes are marked with this symbol in the main instructions. Please read these notes carefully before work begins!
•Adjustment work at the system must only be done by skilled electricians.
General InformationWhen central battery systems are supplied without battery or the type of battery is unknown the tripple chargevoltage is set up with the factory default of 245V (means 2.27V/Z).
According to the type of battery the tripple chargevoltage must be fitted at face.
Adjust the tripple chargevoltage as follows:
1. Press and hold the service pin (1) of the BCM for several seconds until the green LEDs flash alternately. The control unit display is now controlled by the BCM. Make sure that no charge fault exists beforehand as otherwise the CU CGS activates an error display.
2. The voltage „U=“ (2), now shown in the display of the CU CGS control unit, is the float charge voltage to be set. The current displayed, „I=+“ (3), represents the number of located CMs on the CCB bus, 1A = 1CM.
3. Now set the float charge voltage with the „ISO Test+“ and „ISO Test“ buttons (4) according to battery manufacturer specifications.
CAUTION!
The float charge voltage is always set to the corre-sponding value at a temperature of 20° C.
4. To save the voltage, press and hold the service button (1) again until the green LEDs stop flashing. Setting mode is terminated automatically after one minute if the Iso Test buttons are no longer pressed.
1
4
Display at the conrol unit CU CG-S
2 3
Battery Control Module BCM
CEAG Notlichtsysteme GmbHSenatorSchwartzRing 2659494 Soest, GermanyTel.: +49 (0) 2921 69870Fax: +49 (0) 2921 69617Email: info[email protected] Web: www.ceag.de
© 2016 EatonAll Rights ReservedPrinted in GermanyPublication No. IL451043MLOrder No. 40071860193February 2016
EatonEMEA HeadquartersRoute de la Longeraie 71110 Morges, SwitzerlandEaton.eu
14:45:11 02.01.12ČČČČČČČČČČČČČČČČČČČČU=248,0V ċ I=+ 1AT=+23,9 °C BT= 0:00hState of charge 100%
ččččččččččččččččččččCEAG ZB-S Name