Post on 19-May-2020
transcript
Montageanleitung (de) 746 708 / 2009-07a
��Multipol CPV10-VI-P�
Festo SE & Co. KG
Postfach D-73726 Esslingen ++49/(0)711/347-0www.festo.com
1. Teileliste P2 P4 P6 P8
9053d_1
9053d_3
9053d_11
1 Multipol CPV10-VI-P�-D
2 Multipol CPV10-VI-P�-C
3 Dichtungen CPV10-VI-P.M7
2. Vorbereitung zur Montage
9053d_5 und 9053d_12
• Beachten Sie notwendige Maße für den Montage-ausschnitt (! Tabelle).
Um die Schutzart IP65 zu gewährleisten. • Stellen Sie sicher, dass
die Fläche im Bereich der Dichtfläche:
� eben ist. � frei von Riefen und Kratzer
ist.
9053d_2
Montageausschnitt für CPV10-VI-P�-D 1
Type A _ 0,1 B _ 0,1 C _ 0,1 D _ 0,1 N
CPV10-VI-P�-D 1
P2 29 22 40 8 2
P4 29 42 40 28 4
P6 29 62 40 48 6 P8 29 82 40 68 6
9053d_4
Montageausschnitt für CPV10-VI-P�-C 2
Type A _ 0,1 B _ 0,1 C _ 0,1 D _ 0,1 N
CPV10-VI-P�-C 2
P2 53 59 64 62 6
P4 53 79 64 82 6
P6 53 99 64 102 6
P8 53 119 64 122 6
3. Montage
9053d_6
• Drücken Sie alle beigeleg-ten Dichtungen 3 in dieBohrungen der CPV-Ventilinsel.
• Beachten Sie, dass die 3er- und 4er-Dichtungen, die den Endplatten der CPV-Ventilinsel beigelegt sind, nur bei Multipol 2 notwendig sind.
9053d_7
• Positionieren Sie den Mul-tipol 1 bzw. 2 von innen am Montageausschnitt.
9053d_8
9053d_9
• Befestigen Sie den Multi-pol 1 bzw. 2 mit N x M5 korrosionsbeständigen Schrauben nach DIN EN ISO 4762.
• Wählen Sie die Schrau-benlänge l wie folgt. Es muss eine Einschraubtiefe der Schrauben von mind. 7,5 mm bis max. 9,5 mm gewährleistet sein.
9053d_10
• Drehen Sie die Schraubenfest. Halten Sie das zuläs-sige Anziehdrehmoment ein.
9053d_17
Zur Befestigung der Ventilin-sel CPV10: • Beachten Sie die Monta-
gehinweise aus der zuge-hörigen Pneumatik-Beschreibung der Venti-linsel.
1
2
3
3
1 / 2
l � t = 7,5mm � 9,5 mm
1 / 2
5 Nm _ 10%
Assembly instructions (en) 746 708 / 2009-07a
��Multiple connector plate CPV10-VI-P�
Festo SE & Co. KG
Postfach D-73726 Esslingen ++49/(0)711/347-0www.festo.com
1. Parts list P2 P4 P6 P8
9053d_1
9053d_3
9053d_11
1 Multiple connector plateCPV10-VI-P�-D
2 Multiple connector plateCPV10-VI-P�-C
3 Seals CPV10-VI-P.M7
2. Preparing for assembly
9053d_5 und 9053d_12
• Note the dimensions of the cut-out for fitting (! Table).
In order to comply with protection class IP65: • Make sure that the
surface near the sealing surface:
� is flat. � is free of marks and
scratches.
9053d_2
Mounting cut-out for CPV10-VI-P�-D 1
Type A _ 0.1 B _ 0.1 C _ 0.1 D _ 0.1 N
CPV10-VI-P�-D 1
P2 29 22 40 8 2
P4 29 42 40 28 4
P6 29 62 40 48 6 P8 29 82 40 68 6
9053d_4
Mounting cut-out for CPV10-VI-P�-C 2
Type A _ 0.1 B _ 0.1 C _ 0.1 D _ 0.1 N
CPV10-VI-P�-C 2
P2 53 59 64 62 6
P4 53 79 64 82 6
P6 53 99 64 102 6
P8 53 119 64 122 6
3. Assembly
9053d_6
• Press the seals 3 supplied into the holes in the CPV valve terminal.
• Note that the 3 and 4-partseals supplied with the end plates of the CPV valve terminal are only required with multiple connector plate 2.
9053d_7
• Position multiple connector plate 1 or 2 in the mounting cut-out from inside.
9053d_8
9053d_9
• Fasten the multiple con-nector plate 1 or 2 with corrosion resistant N x M5 screws as per DIN EN ISO 4762.
• Select the screw length l as follows. A screw depth of at least 7.5 mm to max. 9.5 mm must be guaranteed.
9053d_10
• Tighten the screws. Maintain the permitted tightening torque.
9053d_17
For mounting the valve terminal CPV10: • Observe the assembly
instructions for the pneumatic section of the valve terminal.
1
2
3
3
1 / 2
1 / 2
5 Nm _ 10%