Post on 15-Jun-2020
transcript
www.dehn.deDE GB
Publication No. 1851 / Update 01.14 Id No. 068243 © Copyright 2014 DEHN + SÖHNE
Blitzschutz/Erdung
MontageanleitungVariabler Endverschluss HVI®power long HVI®long-Leitung
HVI®power vorkonfektioniert HVI®Leitung vorkonfektioniert
2
Inhaltsverzeichnis
1. Sicherheitshinweise .....................................................................................................3
2. Variabler Endverschluss bei der Anwendung mit der HVI®Leitung ...........................4
2.1 Variabler Endverschluss an „Getrennte Ringleitung“ / Attika.....................................52.2 Auslieferungszustand „Distanzhalter mit PA-Element“...............................................6
2.3 Montage „Distanzhalter mit PA-Element“...................................................................72.4 Kürzen „Distanzhalter mit PA-Element“ ......................................................................7
3. Variabler Endverschluss bei der Anwendung mit der HVI®power-Leitung ................8
3.1 Variabler Endverschluss an „Getrennte Ringleitung“ / Attika.....................................93.2 Auslieferungszustand „Variabler Distanzhalter mit Dreibeinstativ“...........................113.2.1 Variabler Distanzhalter mit PA-Element.......................................................................12
3.3 Montage.......................................................................................................................133.3.1 Montagevorbereitung..................................................................................................133.3.2 Einstellen des variablen Distanzhalters nach Trennungsabstand ...............................133.3.3 Zusammenbau..............................................................................................................143.3.4 Dreibeinstativ in die Betonsockel einsetzen................................................................153.3.5 Einsetzen des variablen Distanzhalters .......................................................................16
3.4 Berücksichtigung der Windzone / Windgeschwindigkeit .............................................17
3
1. Sicherheitshinweise
Die Montagearbeiten zum Aufbau des variablen Endverschlusses dürfen nur durch ein qualifiziertes, geschultes Fachpersonal (Blitzschutz-Fachkraft) durchgeführt werden. Anmerkung: Ergänzend hierzu werden entsprechende Produktschulungen bei der Fa. DEHN+SÖHNE ange- boten! Nähere Angaben erhältlich unter: http://www.dehn.de/de/dehnacademy
Die Montage des variablen Endverschlusses ist grundsätzlich nur im Rahmen der in dieser Montageanleitung genannten Vorgaben und Bedingungen zulässig. Vor der Montage des variablen Endverschlusses sind die Komponenten auf ordnungsgemäßen Zustand zu kontrollieren. Sollte eine Beschädigung oder ein sonstiger Mangel festgestellt werden, dürfen die Komponenten nicht montiert werden.
Die Angaben für den variablen Endverschluss gelten nicht für die Montage im Wandbereich sowie am Einspeisepunkt in das Erdungssystem.
Bei erkennbaren bzw. herannahenden Gewittertätigkeiten sind die Montagearbeiten aus Sicherheits- gründen zu unterbrechen. Das Hinzufügen von fabrikat- oder typfremder Komponenten ist unzulässig und führt zum Erlöschen des Gewährleistungsanspruches.
Bei der Montage der Komponenten auf empfindlichen Untergründen wie z.B. Foliendachbahnen usw. ist darauf zu achten, dass keinerlei Beschädigungen entstehen.
Bei den Montagearbeiten empfiehlt es sich eine persönliche Schutzausrüstung zu tragen.
Bei der Anwendung des variablen Endverschlusses in Kombination mit Stützrohr und HVI-Leitungen müssen zusätzlich die Montagevorgaben und Bedingungen der jeweiligen bzw. nachfolgenden Montageanleitungen beachtet werden: HVI®Leitung, vorkonfektioniert Publication No. 1811 HVI®power, Publication No. 1829 HVI®power long, Publication No. 1829 HVI®long-Leitung Verlegung im/am Stützrohr, Publication No. 1841 Die Montageanleitungen stehen im Download-Bereich von DEHN + SÖHNE GmbH + Co.KG zur Verfügung.
Bitte wenden Sie sich bei anwendungstechnischen Fragen an das für Sie zuständige Vertriebsteam oder den Aussendienst-Mitarbeiter in Ihrer Region.
Montageanleitung beachten!
4
1. ®power-Leitung
35
90
704517.5 75
150
10
Durch den variablen Endverschluss und der daraus resultierenden kürzeren Länge des Endverschlusses, kann auf die Montage des zusätzlichen Distanzhalters verzichtet werden (siehe hierzu auch Bild 6 der Montageanleitung Publication No. 1811).
Die Länge des variablen Endverschlusses ergibt sich aus dem errechneten Trennungsabstand in sLuft multipliziert mit dem Faktor 2
Achtung:Der variable Endverschluss kann nur bei einer schwarzen HVI®Leitung angewandt werden. Bei Verwendung einer grauen HVI®Leitung ist der graue Mantel im Endverschlussbereich abzusetzen!
Länge „L“ Endverschluss = Trennungsabstand in sLuft x 2
2. Variabler Endverschluss bei der Anwendung mit der HVI®Leitung
Wird die HVI®Leitung nicht bis zur Erdungsanlage, sondern an Blitzspannung behaftete Teile, (z.B. Attika, Ringleitung) angeschlossen, ist für die effektive Länge des Endverschlusses nachfolgende Fig. 2 ausschlag-gebend (siehe auch Fig. 2.1a, Seite 5 und Fig. 2.1b, Seite 6).Im Bereich unterhalb des Trennungsabstandes "s" 17,5 cm (in Luft) am Erdanschlusselement sind keine besonderen Montageanforderungen (direkter Anschluss) relevant (siehe Fig. 2).
Fig. 2 Variabler Endverschluss
ÄquivalenterTrennungs-abstand "s" (in Luft)
max. variabler Endverschluss HVI®Leitung
MaximumHVI®Leitung
Länge L
Variabler Endverschluss (cm)
5
Fig. 2.1a Variabler Endverschluss an „Getrennte Ringleitung“
2.1 Variabler Endverschluss an "Getrennte Ringleitung" / Attika
Bei mehreren zu schützenden Anlagenteilen ist es sinvoll, die HVI®Leitung nicht einzeln von jeder Fang-einrichtung zur Erdungsanlage zu führen. Die von der Fangeinrichtung kommenden HVI®Leitungen können z.B. an eine "Getrennte Ringleitung oder Attika"angeschlossen werden.Von dieser "Getrennten Ringleitung (Attika)" können dann mehrere Ableitungen zur Erdungsanlage geführt werden. Dies bewirkt eine Reduzierung des Stromaufteilungskoeffizienten kc ab der Höhe der "Getrennten Ringleitung". Der Trennungsabstand "s" wird dadurch kleiner. Für diese Anwendung ist die HVI®Leitung (Trommelware) vorgesehen (siehe auch Fig. 2.1a, Seite 5 und Fig. 2.1b, Seite 6).
Die "Getrennte Ringleitung" muss z.B. auf der Dachebene unter Berücksichtigung des errechneten Tren-nungsabstandes "s" auf Distanzhaltern und Betonsockel verlegt werden.
Anschlusselement
Getrennte Ringleitung
Distanzhalter
Variabler Endverschluss
35 cm - max. 90 cm (Standard)L= sLuft x 2
sLu
ft HVI®Leitung
min
. Län
ge, L
= s
Luft
Potentialausgleich des Gebäudes
Distanzhalter mit PA-Element und MV-Klemme,
17 kg, Art.-Nr. 102 010
Leitungshalter
Verbindung zum
Werkstoff AlArt.-Nr. 105 275
Betonsockelz.B. Art.-Nr. 253 239oder 275 229
6
2
1
3
1
23
min
. Län
ge, L
= s
Luft
sLu
ft
L= sLuft x 2
HVI®Leitung
2.2 Auslieferungszustand „Distanzhalter mit PA-Element“ Im Auslieferungszustand ist der Distanzhalter in Schlauchfolie verpackt. Die MV-Klemme ist dem Distanzhalter lose beigepackt (siehe Fig.2.2).
PA-Element, Ø 20 mm (Leitungshalter)Alu-Stab, Ø 16 mmMV-Klemme, Alu, Rd 8-10 / Rd 16 mm,für den Anschluss an den Funktionspotentialausgleich
Fig. 2.2 Distanzhalter mit PA-Element
Verbindung zumPotentialausgleich
des Gebäudes
35 cm - max. 90 cm (Standard)
Variabler Endverschluss
Attika
Anschlusselement
Fig. 2.1b Variabler Endverschluss an „Attika“
Leitungshalterz.B. Art.-Nr. 253 239
7
25 Nm
5 Nm
35
90
704517.5 75
150
10
2.3 Montage
Die Montage des Distanzhalters mit PA-Element erfolgt in einem 17 kg Betonsockel. Der Distanzhalter wird in die Betonsockelaussparung eingesteckt. Zur mechanischen Befestigung wird der Distanzhalter mit einem Befestigungskeil eingekeilt. Die MV-Klemme wird im unteren Bereich des Distanzhalters montiert. Die angegebenen Anzugsdrehmomente sind zu beachten (siehe Fig. 2.3).
2.4 Kürzen des Distanzhalters mit PA-Element entsprechend des Trennungsabstandes „sLuft“
Der Distanzhalter kann entsprechend des errechneten Trennungsabstandes gekürzt werden! Die Länge L des Distanzhalters muss mindestens dem Trennungsabstand „sLuft“ entsprechen. L ist die Länge von der Unterkante des PA-Elementes bis zur Oberkante des Betonsockels (siehe Fig. 2.3).
Anmerkung: Zum Schutz von Dachbahnen oder empfindlichen Dachoberflächen wird bei der Montage der
Betonsockel die Verwendung von Unterlegplatten Art.-Nr. 102 050 empfohlen (siehe Fig. 2.3).
Betonsockel-aussparrung
MV-Klemme, Alu,Rd 8-10 / Rd 16 mm
Distanzhalter (Alu-Stab)
PA-Element, Ø 20 mm(Leitungshalter)
BetonsockelArt.-Nr. 102 010
UnterlegplatteArt.-Nr. 102 050
Befe
stig
ungs
keil
ÄquivalenterTrennungsabstand "s" (in Luft)
max. variabler Endverschluss HVI®Leitung
Leitung
Länge L
Variabler Endverschluss (cm)
Läng
e, L
= s
Luft
Läng
e, L
= s
Luft
Maximum ®HVI
Fig. 2.3 Distanzhalter mit PA-Element
8
75
150
35
100
200
180
5010 9017.5
Die Länge des variablen Endverschlusses ergibt sich aus dem errechneten Trennungsabstand in sLuft multipliziert mit dem Faktor 2
Länge „L“ Endverschluss = Trennungsabstand in sLuft x 2
3. Variabler Endverschluss bei der Anwendung mit der HVI®power-Leitung
Wird die HVI®power-Leitung nicht bis zur Erdungsanlage, sondern an Blitzspannung behaftete Teile, (z.B. Attika, Ringleitung) angeschlossen, ist für die effektive Länge des Endverschlusses nachfolgende Fig. 3) ausschlaggebend (siehe auch Fig. 3.1a, Seite 9 und Fig. 3.1b, Seite 10).Im Bereich unterhalb des Trennungsabstandes "s" 17,5 cm (in Luft) am Erdanschlusselement sind keine besonderen Montageanforderungen (direkter Anschluss) relevant (siehe Fig. 3).
ÄquivalenterTrennungsabstand "s" (in Luft)
LängeVariabler Endverschluss (cm)
Fig. 3 Variabler Endverschluss
max. variabler Endverschluss HVI®power- Leitung
maximum HVI®Leitung
9
Art.-Nr. 253 333 od. 253 334
Verbindung zum
des Gebäudes
min
. Län
ge, L
= s
Luft
HVI®power-Leitung
Leitungshalter
Getrennte Ringleitung
Distanzhalter
Anschlusselement35 cm - max. 150 cm (Standard)
Variabler EndverschlussL= sLuft x 2
Fig. 3.1a Variabler Endverschluss an „Getrennte Ringleitung“
Potentialausgleich
Variabler Distanzhaltermit Dreibeinstativ sowie PA-Element, Art.-Nr.105 279
3.1 Variabler Endverschluss an "Getrennte Ringleitung" / Attika
Bei mehreren zu schützenden Anlagenteilen ist es sinvoll, die HVI®power-Leitung nicht einzeln von jeder Fangeinrichtung zur Erdungsanlage zu führen. Die von der Fangeinrichtung kommenden HVI®power-Leitungen können z.B. an eine "Getrennte Ringleitung oder Attika" angeschlossen werden. Von dieser "Getrennten Ringleitung (Attika)" können dann mehrere Ableitungen zur Erdungsanlage geführt werden. Dies bewirkt eine Reduzierung des Stromaufteilungskoeffizienten kc ab der Höhe der "Getrennten Ringleitung". Der Trennungsabstand "s" wird dadurch kleiner. Für diese Anwendung ist die HVI®power-Leitung (Trommelware) vorgesehen (siehe auch Fig. 3.1a, Seite 9 und Fig. 3.1b, Seite 10)
Die "Getrennte Ringleitung" muss z.B. auf der Dachebene unter Berücksichtigung des errechneten Tren-nungsabstandes "s" auf Distanzhaltern und Betonsockel verlegt werden.
sLu
ft
10
Variabler Distanzhaltermit Dreibeinstativ sowie PA-Element, Art.-Nr.105 279
35 cm - max. 150 cm (Standard)
L= sLuft x 2Variabler Endverschluss
Verbindung zumPotentialausgleich
des Gebäudes
Attika
LeitungshalterArt.-Nr. 253 333 od. 253 334
Anschlusselement
Fig. 3.1b Variabler Endverschluss an „Attika“
HVI®power-Leitung
min
. Län
ge, L
= s
Luft
SLu
ft
1
1
234
5
6
6
789
7
89
2
3
4
5
11
3.2 Auslieferungszustand „Variabler Distanzhalter mit Dreibeinstativ
Im Auslieferungszustand ist das Dreibeinstativ zusammengeklappt (siehe Fig. 3.2). Der variable Distanzhalter ist separat beigelegt. (siehe Fig.3.2.1, Seite 12).
Für die Anwendung mit der HVI®power- Leitung
Aufnahme (Anpassung an die Dachneigung max. 10°)Sechskantmutter M8Sechskantschraube M8Sechskant-Sicherungsmutter M8Hammerkopfschraube M8 x 20Hammerkopfschraube M8 x 30Doppelüberleger NIRO Rd 8 -10 (für Funktionspotentialausgleich)Standfuss NIROStandfuss NIRO, vormontiert
Fig. 3.2 Dreibeinstativ
1
2
3
4
1
23
4
12
15 Nm
5 Nm
610 mm 1095 mm
PA-Element, Ø 27 - 30 mm, (Leitungshalter)NIRO-Stab verstellbar Ø 13 mmArretierungsschraube,Sechskantschraube M8 x10Abstandsrohr Ø 22 mm, NIRO L = 610 mm
Verstellbereich:610 - 1095 mm
Fig. 3.2.1 Variabler Distanzhalter mit PA-Element
13
-75
150
35
100
200
180
5010 9017.5
3.3. Montage
3.3.1 Montagevorbereitung, Platzierung der Betonsockel In Abhängigkeit der örtlichen Gegebenheiten (siehe auch Fig. 3.1a, Seite 9 und Fig. 3.1b, Seite 10) muss für jeden Standfuss des Dreibeinstatives ein Betonsockel aufgestellt werden. Die Montageabstände der 17 kg Betonsockel resultieren aus dem Radius des Dreibeinstatives (siehe Fig. 3.3.1).
3.3.2 Einstellen des variablen Distanzhalters entsprechend des Trennungsabstandes „sLuft“
Der variable Distanzhalter wird entsprechend des errechneten Trennungsabstandes in der Höhe (mittels der beiden Arretierungsschrauben) eingestellt. Die einzustellende Länge L des Distanzhalter muss mindestens dem Trennungsabstand „sLuft“ entsprechen. L ist die Länge von der Unterkante des Leitungshalter bis zur Oberkante der Auf- nahme des Statives (siehe Fig. 3.3.1).
Anmerkung: Zum Schutz von Dachbahnen oder empfindlichen Dachoberflächen, wird bei der Montage der
Betonsockel die Verwendung von Unterlegplatten Art.-Nr. 102 050 empfohlen (siehe Fig. 3.3.1).
ÄquivalenterTrennungsabstand "s" (in Luft)
LängeVariabler Endverschluss (cm)
max. variabler Endverschluss HVI®power- Leitung
maximum HVI®Leitung
Radius 320 mm
Fig. 3.3.1 Platzierung der Betonsockel
BetonsockelArt.-Nr. 102 010
Betonsockel-aussparrung
UnterlegplatteArt.-Nr. 102 050
Anzugsdrehmoment15 Nm beachten!
Befestigungskeil
Läng
e, L
= s
Luft
14
1
234
5
6
13
123
2
44
1
1
4
46
4
4
5
2
1
3
3
1
2
2
3.3.3 Zusammenbau Zum Zusammenbau des variablen Dreibeinstatives müssen die beiden äußeren Sechskant- Sicherungsmuttern M8 aufgeschraubt und mit den beiden Hammerkopfschrauben M8 x 20 vom Stativ abgenommen werden. Die innenliegende Sechskant-Sicherungsmutter M8 an den beiden klappbaren Standfüßen werden nur gelockert. Danach werden die beiden Standfüße nach außen aufgeklappt und mittels der Sechskant-Sicherungsmuttern M8 und der Hammerkopfschrauben wieder verschraubt. Die angegebenen Anzugsdrehmomente sind dabei zu beachten (siehe Fig. 3.3.3).
Äußere Sechskant-Sicherungsmutter M8Hammerkopfschraube M8 x 20Innenliegende Sechskant-Sicherungsmutter M8Standfuss NIRO, L = 299 mmStandfuss NIRO, L = 320 mmHammerkopfschraube M8 x 20(vormontiert; Anzugsdrehmoment 15 Nm prüfen!)
Fig. 3.3.3 Variables Dreibeinstativ
Anzugsdrehmoment15 Nm beachten!
15
3.3.4 Dreibeinstativ in die Betonsockel einsetzen
Nach dem Zusammenbau wird das Dreibeinstativ von oben an die Betonsockel herangeführt und mit den drei Standfüßen in die jeweilige Bohrung der Betonsockel eingesetzt. Die drei Standfüße sind mit je einem Befestigungskeil in der jeweiligen Betonsockelbohrung festzu- keilen (siehe Fig. 3.3.4).
Fig. 3.3.4 Dreibeinstativ in die Betonsockel einsetzen
Standfuß
Befestigungskeil
16
3.3.5 Einsetzen des variablen Distanzhalters
Der variable Distanzhalter wird von oben bis zum Anschlag in die Aufnahme des Dreibeinstatives eingeführt und mittels der drei Arretierungsschrauben M8 x 25 der Aufnahme festgeschraubt und gekontert. Die Aufnahme (konisch) des Dreibeinstatives ermöglicht ein Nachjustieren der Montage- lage des Distanzhalters bis zu max.10°. Das Nachjustieren erfolgt durch Verstellen der Arretierungs schrauben der Aufnahme (siehe Fig. 3.3.5).
Verstellbereich:610 - 1095 mm
Fig. 3.3.5 Distanzhalter einsetzen
Arretierungsschrauben M8 x 10
Aufnahme (konisch)
Anschluss an den Funktionspotential-ausgleich
PA-Element, Ø 27 - 30 mm (Leitungshalter)
Abstandsrohr, Ø 22 mm
NIRO-Stab verstellbar, Ø 13 mm
3 xArretierungsschraube(SechskantschraubeM8 x 25) mit Kontermutter
Anzugsdrehmoment15 Nm beachten!
Anzugsdrehmoment5 Nm beachten!
Läng
e, L
= S
Luft
17
München
Augsburg
Regensburg
Nürnberg
Würzburg
Stuttgart
Freiburg
Saarbrücken Mannheim
FrankfurtWiesbaden
Köln
Düsseldorf
Bonn
EssenDortmund
Erfurt Chemnitz
DresdenLeipzig
Halle
Magdeburg
Berlin
PotsdamHannover
Bremen
HamburgSchwerin
RostockKiel
3.4 Berücksichtigung der Windzone / Windgeschwindigkeit
Bei der Errichtung von Fangeinrichtungen müssen die Windzonen berücksichtigt werden. Die Wind- zonen sind regional unterschiedlich. Beim Errichten von Fangeinrichtungen außerhalb des Bundes- gebietes sind die entsprechenden landesspezifischen Angaben zu den Windzonen / Windge- schwindigkeit zu berücksichtigen (siehe Fig. 3.4).
In die Berechnung der tatsächlichen zu erwartenden Windlastbeanspruchung geht neben der zonen- abhängigen Windlast auch die Gebäudehöhe und die örtlichen Gegebenheiten (Gebäude einzeln stehend, im offenen Gelände oder eingebettet in andere Bebauung) mit ein. Bei der Auslegung freistehender Fangstangen müssen aus Sicht der Windlastbeanspruchung folgen- de Anforderungen erfüllt werden:
Sicherheit gegen Kippen Sicherheit gegen Bruch
Windzone: 2 (Windgeschwindigkeit 142 km/h) Geländekategorie: Vorstadtgebiet, Industriegebiet Höhe über Flur: max. 40 m Höhe ü. Meeresspiegel: bis 800 m ü. NN
Fig. 3.4 Berücksichtigung der Windzone / Windgeschwindigkeit
Parameter für die Berechnung: Geländekategorie III: Vorstadt, Industriegebiet Gebäudehöhe: 40 m Höhe ü. Meeresspiegel: bis 800 m über Normal Null
Windzone Grundgeschwin-digkeit (fix)
Windzone 1 22,5 m/s 128 km/h
Windzone 2 25,0 m/s 142 km/h
Windzone 3 27,5 m/s 156 km/h
Windzone 4 30,0 m/s 170 km/h
Böenwindge-schwindigkeit
18
75
150
35
100
200
180
5010 9017.5Radius 320 mm
BetonsockelArt.-Nr. 102 010
Betonsockel-aussparrung
UnterlegplatteArt.-Nr. 102 050
Anzugsdrehmoment15 Nm beachten!
Befestigungskeil
ÄquivalenterTrennungs-abstand "s" (in Luft)
Variabler Endverschluss (cm)
max. variabler Endverschluss HVI®power- Leitung
maximum HVI®power-Leitung
Länge
Läng
e, L
= s
Luft
Fig. 3.3.1 Platzierung der Betonsockel
HVI®
19
Überspannungsschutz DEHN + SÖHNE Hans-Dehn-Str. 1 Tel. +49 9181 906-0Blitzschutz/Erdung GmbH + Co.KG. Postfach 1640 Fax +49 9181 906-1100Arbeitsschutz 92306 Neumarkt info@dehn.deDEHN schützt. Germany www.dehn.de
www.dehn.deDE GB
Publication No. 1851 / Update 01.14 Id No. 068243 © Copyright 2014 DEHN + SÖHNE
Installation instructionsVariable sealing end HVI®power long HVI®long Conductor
Lightning protection/earthing
Prewired HVI®power Previered HVI® Conductor
2
Contents
1. Safety instructions .......................................................................................................3
2. Variable sealing end in case of HVI®Leitung Conductors ..........................................4
2.1 Variable sealing end on isolated ring conductors/cappings of the roof parapet ........52.2 As-delivered condition of the spacer with EB element ...............................................6
2.3 Installation of the spacer with EB element .................................................................72.4 Adjusting the height of the spacer with EB element...................................................7
3. Variable sealing end in case of HVI®power Conductors ...........................................8
3.1 Variable sealing end on isolated ring conductors/cappings of the roof parapet ........93.2 As-delivered condition of the variable spacer with tripod..........................................113.2.1 Variable spacer with EB element .................................................................................12
3.3 Installation...................................................................................................................133.3.1 Installation preparation ...............................................................................................133.3.2 Adjusting the height of the variable spacer according to the separation distance....133.3.3 Assembly ......................................................................................................................143.3.4 Inserting the tripod into the concrete base.................................................................153.3.5 Inserting the variable spacer.......................................................................................16
3.4 Installation with regard to the wind zone/wind speed ...............................................17
3
1. Safety instructions
Only qualified and trained personnel (lightning protection specialists) may install the variable sealing end. Note: We recommend to visit a special training course on HVI® products held by DEHN+SÖHNE.
The variable sealing end may only be installed under the conditions shown and referred to in these installation instructions. Prior to installation of the variable sealing end, the components must be examined for good order and condition. If damage or any other defect is found, the components must not be installed
The information on the variable sealing end provided in these installation instructions does not apply if it is installed on a wall and at the entry point into the earth-termination system.
For safety reasons, installation work must be stopped as soon as a thunderstorm approaches/is noticed. Installing components from other manufacturers or of other types is not permitted and will void warranty.
When mounting the components on sensitive surfaces such as foil roofings, etc., it must be ensured that these components are not damaged.
It is advisable to wear personal protective equipment during installation work.
When using the variable sealing end in conjunction with a supporting tube and HVI Conductors, the relevant installation instructions must be additionally observed: Prewired HVI® Conductor (Publication No. 1811) HVI®power, (Publication No. 1829) HVI®power long, (Publication No. 1829) Installing HVI®long Conductors inside/outside the supporting tube, (Publication No. 1841) These installation instructions can be downloaded from the DEHN + SÖHNE GmbH + Co.KG homepage.
For application-specific questions, please contact the relevant sales team or your local DEHN representative.
Observe the installation instructions!
4
1. ®power-Leitung
35
90
704517.5 75
150
10
Due to the variable sealing end and the resulting reduced length of the sealing end, no additional spacer must be installed (see Fig. 6 of installation instructions No. 1811).
The length of the variable sealing end can be determined by means of the calculated separation distance sair multiplied by the factor 2.
Attention:The variable sealing end may only be used for black HVI®Conductors.When using grey HVI® Conductors, the grey sheath must be stripped in the sealing end range!
Length „L“of the sealing end = separation distance sair x 2
Fig. 2 Variable sealing end
Equivalent separation distance "s" (in air)
Maximum variable sealing endHVI® Conductor
Maximum Length L
Variable sealing end (cm)
HVI® Conductor
2. Variable sealing end in case of HVI® Conductors
If HVI® Conductors are not connected to the earth-termination system, but to parts carrying lightning voltage (e.g. metal capping of the roof parapet, ring conductor), Fig. 2 must be observed for the effective length of the sealing end (see also Fig. 2.1a, page 5 and Fig. 2.1b, page 6).No special installation conditions (direct connection) must be considered in the area below the separation distance "s" of 17.5 cm (in air) on the earth connection element (see Fig. 2).
5
2.1 Variable sealing end on isolated ring conductors/metal cappings of the roof parapet
If several parts of an installation are to be protected, it is not advisable to lead the HVI®Conductors from each air-termination system to the earth-termination system. The HVI®Conductors from the air-termination system can be connected to e.g. an isolated ring conductor or to the metal capping of the roof parapet. From this isolated ring conductor (metal capping of the roof parapet), several down conduc-tors can be routed to the earth-termination system. This reduces the partitioning coefficient kc downstream of the isolated ring conductor and thus also the separation distance “s”. HVI®Conductors (reeled up on a drum) can be used for this purpose (see also Fig. 2.1a, page 5 and Fig. 2.1b, page 6).
The isolated ring conductor must be installed on spacers and concrete bases e.g. on the roof level. The calculated separation distance “s” must be observed.
spacer with EB element and MV clamp (aluminium), Part No. 105 275 conductor holder,
e.g. Part No. 253 339 or 275 229
min
. len
gth,
L =
sai
r s
air
L= sair x 2
Fig. 2.1a Variable sealing end on an isolated ring conductor
variable sealing end
35 cm - max. 90 cm (standard)
HVI® Conductor
connection to the equipotential bonding system of the building
isolated ring conductor
spacer
connection element
concrete base17 kg, Part No. 102 010
6
2
1
3
1
23
min
. Len
gth,
L =
sLu
ft s
Luft
L= sair x 2
HVI®Conductor
2.2 As-delivered condition of the spacer with EB element When delivered, the spacer is wrapped in a tubular film. The MV clamp is loosely delivered with the spacer (see Fig. 2.2).
EB element, Ø 20 mm (conductor holder)Aluminium rod,, Ø 16 mmMV clamp, aluminium, Rd 8-10 / Rd 16 mm, to be connected to the functional equipotential bonding system
Fig. 2.2 Spacer with EB element
35 cm - max. 90 cm (standard)
variable sealing end
metal capping of the roof parapet
connection element
Fig. 2.1b Variable sealing end on the metal capping of the roof parapet
conductor holder, e.g. Part No. 253 239 or 275 229
connection to the equipotential bonding system of the building
7
25 Nm
5 Nm
35
90
704517.5 75
150
10
2.3 Installation
The spacer with EB element is installed into a 17 kg concrete base. Move the spacer closer to the concrete base from above and insert it into the hole of the concrete base. To mechanically fix the spacer, insert a wedge into the hole of the concrete base. Mount the MV clamp in the lower part of the spacer. Observe the relevant tightening torques (see Fig. 2.3).
2.4 Adjusting the height of the spacer with EB element according to the separation distance „sair“ The height of the spacer can be adjusted according to the calculated separation distance „sair“. The length L of the spacer must be at least equal to the separation distance „sair“. L is the length between the lower edge of the EB element and the top edge of the concrete base (see Fig. 2.3).
Note: To protect roof sheetings or sensitive roof surfaces, it is advisable to position concrete bases on
support plates (Part No. 102 050) (see Fig. 2.3).
hole of the concrete base
MV clamp, aluminium,Rd 8-10 / Rd 16 mm
spacer (aluminium rod)
EB element, Ø 20 mm(conductor holder)
concrete basePart No. 102 010
support platePart No. 102 050
wed
ge
Maximum variable sealing endHVI®Conductor
Length L
Variable sealing end (cm)
leng
th L
= s
air
leng
th L
= s
air
Fig. 2.3 Spacer with EB element
Equivalent separation distance “s” (in air)
Maximum HVI® Conductor
8
75
150
35
100
200
180
5010 9017.5
The length of the variable sealing end can be determined by means of the calculated separation distance sair multiplied by the factor 2.
3. Variable sealing end in case of HVI®power Conductors
If the HVI®power Conductor is not connected to the earth-termination system, but to parts carrying lightning voltage (e.g. metal capping of the roof parapet, ring conductor), Fig. 3 must be observed for the effective length of the sealing end (see also Fig. 3.1a, page 9 and Fig. 3.1b, page 10).No special installation conditions (direct connection) must be considered in the area below the separation distance “s” of 17.5 cm (in air) on the earth connection element (see Fig. 3).
LengthVariable sealing end (cm)
Fig. 3 Variable sealing end
Maximum variable sealing end HVI®power Conductor
Equivalent separation distance “s” (in air)
Maximum HVI®power Conductor
Length “L” of the sealing end = separation distance sair x 2
9
3.1 Variable sealing end on isolated ring conductors/metal cappings of the roof parapet
If several parts of an installation are to be protected, it is not advisable to lead the HVI®power Conduc-tors from each air-termination system to the earth-termination system. The HVI®power Conductors arriving from the air-termination system can be connected to e.g. an isolated ring conductor or to the metal capping of the roof parapet. From this isolated ring conductor (metal capping of the roof parapet), several down conductors can be routed to the earth-termination system. This reduces the partitioning coefficient kc downstream of the isolated ring conductor and thus also the separation distance “s”. HVI®power Conductors (reeled up on a drum) can be used for this purpose (see Fig. 3.1a, page 9 and Fig. 3.1b, page 10).
The isolated ring conductor must be installed on spacers and concrete bases e.g. on the roof level. The calculated separation distance “s” must be observed.
Part No. 253 333 or 253 334
min
. len
gth
L =
sai
r
HVI®power Conductor
conductor holder
isolated ring conductor
spacer
connection element35 cm - max. 150 cm (standard)
variable sealing end
Fig. 3.1a Variable sealing end on an isolated ring conductor
variable spacer with tripod and EB element Part No.105 279
sai
r
connection to the equipotenti-al bonding system of the
building
L= sair x 2
10
variable spacer with tripod and EB element, Part No.105 279
35 cm - max. 150 cm (standard)
L= sair x 2variable sealing end
connection to the equipotential bonding system of the building
metal capping of the roof parapet
conductor holderPart No. 253 333 or 253 334
connection element
Fig. 3.1b Variable sealing end on the metal capping of the roof parapet
HVI®power Conductor
min
. len
gth,
L =
sai
r S
air
1
1
234
5
6
6
789
7
89
2
3
4
5
11
3.2 As-delivered condition of the variable spacer with tripod
When delivered, the tripod is hinged (see Fig. 3.2). The variable spacer is loosely delivered with the tripod (see Fig. 3.2.1, page 12).
For use with HVI®power Conductor
Support (adaptation to the roof pitch up to max. 10°)M8 hexagon nutM8 hexagon screwM8 hexagon lock nutHammer-head screw M8 x 20Hammer-head screw M8 x 30Stainless steel double cleat, Rd 8-10 mm (for functional equipotential bonding)Stainless steel footPre-mounted stainless steel foot
Fig. 3.2 Tripod
1
2
3
4
1
23
4
12
15 Nm
5 Nm
610 mm 1095 mm
EB element, Ø 27-30 mm (conductor holder) Adjustable stainless steel rod, Ø 13 mmLocking screw, hexagon screw M8 x10
Stainless steel spacer tube, Ø 22 mm, L = 610 mm
adjusting range:610 - 1095 mm
Fig. 3.2.1 Variable spacer with EB element
13
-75
150
35
100
200
180
5010 9017.5
3.3. Installation
3.3.1 Installation preparation, positioning the concrete bases Depending on the local conditions (see also Fig. 3.1a, page 9 and Fig. 3.1b, page 10), a concrete base must be mounted for each foot of the tripod. The mounting distances of the 17 kg concrete bases depend on the mounting radius of the tripod (see Fig. 3.3.1).
3.3.2 Adjusting the height of the variable spacer according to the separation distance “sair“
The height of the variable spacer is adjusted according to the calculated separation distance (by means of the two locking screws). The length L of the spacer to be adjusted must be at least equal to the separation distance “sair“. L is the length between the lower edge of the conductor holder and the top edge of the support of the tripod (see Fig. 3.3.1).
Note:To protect roof sheetings or sensitive roof surfaces, it is advisable to position the concrete bases on support plates (Part No. 102 050) (Fig. 3.3.1).
Equivalent separation distance “s” (in air)
Variable sealing end (cm)
Maximum variable sealing end HVI®power- Conductor
maximum HVI®power conductor
Radius of 320 mm
Fig. 3.3.1 Positioning the concrete bases
concrete basePart No. 102 010
hole of the concrete base
support platePart No. 102 050
Observe a tightening torque of 15 Nm!
wedge
Leng
th, L
= s
air
14
1
234
5
6
13
123
2
44
1
1
4
46
4
4
5
2
1
3
3
1
2
2
3.3.3 Assembly To assemble the variable tripod, loosen the two outer M8 hexagon locking nuts and remove them from the tripod together with the two hammer-head screws M8 x 20. Loosen the inner M8 hexagon lock nut on both hinged feet. Fold the two feet to the outside and screw them together again by means of the M8 hexagon lock nuts and the hammer-head screws. To this end, observe the relevant tightening torques (see Fig. 3.3.3).
Outer M8 hexagon lock nutHammer-head screw M8 x 20Inner M8 hexagon lock nutStainless steel foot, L = 298.5 mmStainless steel foot, L = 320 mmHammer-head screw M8 x 20 (pre-mounted; check tightening torque!)
Fig. 3.3.3 Variable tripod
Observe a tightening torque of 15 Nm!
15
3.3.4 Inserting the tripod into the concrete base
After assembly, move the tripod closer to the concrete bases from above and insert the three feet into the relevant hole of the concrete base. Fix each of the three feet in the relevant hole of the concrete base by means of a wedge (see Fig. 3.3.4).
Fig. 3.3.4 Inserting the tripod into the concrete bases
foot
wedge
16
3.3.5 Inserting the variable spacer
Insert the variable spacer from above into the support of the tripod as far as it will go and tighten it using the three locking screws M8 x 25 of the support. The support (conical) allows to adjust the position of the spacer up to max. 10° by means of the locking screws (see Fig. 3.3.5).
adjusting range:610 - 1095 mm
locking screws M8 x 10
support (conical)
connection to the functional equipotential bonding system
EB element, Ø 27-30 mm (conductor holder)
spacer tube, Ø 22 mm
adjustable stainless steel rod, Ø 13 mm
3 xlocking screw (hexagon screwM8 x 25)
Observe a tightening torque of 5 Nm!
Observe a tightening torque of 5 Nm!
Leng
th, L
= S
air
Fig. 3.3.5 Inserting the spacer
17
München
Augsburg
Regensburg
Nürnberg
Würzburg
Stuttgart
Freiburg
Saarbrücken Mannheim
FrankfurtWiesbaden
Köln
Düsseldorf
Bonn
EssenDortmund
Erfurt Chemnitz
DresdenLeipzig
Halle
Magdeburg
Berlin
PotsdamHannover
Bremen
HamburgSchwerin
RostockKiel
3.4 Installation with regard to the wind zone/wind speed
When installing air-termination systems, the wind zones must be observed. These wind zones differ from region to region. When installing air-termination systems outside of Germany, the country- specific requirements concerning wind zones/wind speeds must be considered (see Fig. 3.4).
To calculate the actual wind load to be expected, the zone-dependent wind load, building height and local conditions (detached building, building in open terrain or building surrounded by other buildings) must be considered. When designing self-supporting air-termination rods, the following requirements must be fulfilled with regard to the wind load: Tilt resistance Break resistance
Wind load zone: 2 (wind speed up to 142 km/h) Site category: suburban, industrial area Height above ground: max. 40 m Height above sea level: 800 m above sea level
Fig. 3.4 Installation with regard to the wind zone/wind speed
Parameters for calculation: Environment III: suburban, industrial area Height of the building: 40 m Height above sea level: up to 800 m above sea level
wind zone base wind speed (fix)
wind zone 1 22,5 m/s 128 km/h
wind zone 2 25,0 m/s 142 km/h
wind zone 3 27,5 m/s 156 km/h
wind zone 4 30,0 m/s 170 km/h
gust wind speed
18
75
150
35
100
200
180
5010 9017.5Radius of 320 mm
concrete basePart No. 102 010
hole of the concrete base
support platePart No. 102 050
Observe a tightening torque of 5 Nm!
wedge
Equivalent separation distance “s” (in air)
Variabler Endverschluss (cm)
Maximum variable sealing end HVI®power- Conductor
maximum HVI®power conductor
Länge
Leng
th, L
= s
air
Fig. 3.3.1 Positioning of the concrete bases
19
Surge Protection DEHN + SÖHNE Hans-Dehn-Str. 1 Tel. +49 9181 906-0Lightning Protection / earthing GmbH + Co.KG. Postfach 1640 Fax +49 9181 906-1100Safety Equipment 92306 Neumarkt export@dehn.deDEHN schützt. Germany www.dehn.de